GReddy Turbo Parts List
The following are the parts list from the GReddy instruction manual. I will make references back to the parts and since the pictures in the manual are not that great, the pictures should help some.
| Part # | Quantity | Part Description (NOTES) |
Part Photo |
| 1 | 1 | TD-04H 15H 8.5cm Turbo |  |
| 2 | 1 | EX Manifold |  |
| 3 | 1 | Turbo Outlet Adapter |  |
| 4 | 1 | Front Pipe - 50mm Steel (down pipe or a-pipe) |
 |
| 5 | 1 | Air Intake Tube A-1 60mm Steel |  |
| 6 | 1 | Charge Pipe C-1 60mm Steel (NOT REQUIRED if you use my method of routing the charge pipe) |
 |
| 7 | 1 | Charge Pipe C-2 60mm Steel (NOTE! Due to a change in the product it has three charge pipes and not two - this is actually TWO pipes) |
 |
| 8 | 1 | Breather Hose 10mmX400mm (NOT REQUIRED) |
 |
| 9 | 1 | Oil Pressure Hose - 800mm SUS |  |
| 10 | 1 | Oil Pressure Hose - Banjo Union, small, male and female 10x1.24mm |  |
| 11 | 2 | Oil Pressure Hose - Copper gasket small |  |
| 12 | 1 | Oil Pressure Hose - 3-Way T 1/8 NPT |  |
| 13 | ?3? | Oil Pressure - Straight Union 1/8 pt (SILVER ONE NOT REQUIRED) |
<-- Not
required |
| 14 | 1 | Oil Return Flange Tube - 15mm Turbo Side |  |
| 15 | 1 | Oil Return Flange Tube - 15mm Oil Pan Side |  |
| 16 | 1 | Oil Return Hose - 19mmX300mm (NOT REQUIRED) |
 |
| 17 | 2 | Oil Return Hose Band - 19mm |
 |
| 18 | 2 | Oil Return Flange Gasket |  |
| 19 | 2 | Silicone Hose - 50mmX70mm Straight |  |
| 20 | 2 | Silicone Host - 60mmX70mm Straight |  |
| 21 | 2 | Hose Band - 50mm - Clamp #32 |
 |
| 22 | 8 | Hose Band - 60mm - Clamp #36 |  |
| 23 | 2 | Hose Band - 10mm - Clamp #5 (NOT REQUIRED) |
 |
| 24 | 1 | 8mm to 8mm Hose Union (NOT REQUIRED) |
 (not right!?) |
| 25 | 1 | Turbine Gasket IN |  |
| 26 | 1 | Turbine Gasket OUT |  |
| 27 | 1 | Muffler Adapting Gasket |  |
| 28 | 1 | Heat Shield |  |
| 29 | 1 | Heat Resistant Cloth 100mmX100mm |  |
| 30 | 10 | Tie-Wrap (Zip-Ties) |  |
| 31 | 1 | Airinx Air Filter |  |
| 32 | 1 | Universal Airinx Adapter 60mm |  |
| 33 | 1 | Secondary Fuel Pressure Regulator
(NOT REQUIRED - with ZDYNE ECU) |
 |
| 34 | 1 | High Pressure Fuel Injection hose 6mmX500mm (NOT REQUIRED) |
<no picture> |
| 35 | 1 | Fuel Management Unit (NOT REQUIRED) |
 |
| 36 | 3 | Hose Band 6mm (For Fuel Pressure) (NOT REQUIRED) |
 |
| 37 | 8 | Wire Connector - male and female (NOT REQUIRED) |
 |
| 38 | 2 | T-Wire Connector (NOT REQUIRED) |
<no picture> |
| 39 | 1 | Vacuum Hose (for secondary fuel regulator) 4mmX500mm
(NOT REQUIRED) |
 |
| 40 | 1 | Tee for Vacuum - 4mm (NOT REQUIRED) |
 |
| 41 | 4 | Sheet Metal Screw (NOT REQUIRED) |
|
| 42-50 | Misc | Various Bolts, Washers and Nuts (SOME NOT REQUIRED) |
 |
| 1 | Photo-Copied Manual This thing is useless - poor quality photocopy, poor photos (line drawings) and incorrect information. Throw it away! |
 |
|
| 1 Each | These are not listed in the GReddy parts list. They
are for connecting the charge pipe to the throttle body and two charge
pipes together (on the standard kit) (NOT REQUIRED if you used my charge tube method) |
 |